DC BLOCKERS | EVO3 NOVA
THE SELECT SERIES
EVO3 NOVA
EVO3 Nova 是一款最先進的被動式電源處理系統，內建全面性的直流消除功能，適合大型的音響系統或家庭劇院。該系統擁有十二組獨立濾波電源插座，其中八組為 10A 電流供訊源設備使用；另外四組為 16A 電流，專供應功率擴大機、主動式超低音、主動式喇叭等。此外，還融入Titan獨特的精簡版直接耦合（Direct-Coupled©）技術。在整體上提供了一個全方位的系統方案。
The EVO3 Nova is a state-of-the-art passive power cleaning system incorporating full DC cancellation. It is ideal for large scale audio systems or home theatre installations. The system offers twelve independently filtered power outlets, eight rated at 10A for source components and four rated at 16A. These are designed for high current electronics, for example power amplifiers, active loudspeakers, or subwoofers. They also feature a slightly pared down version of the Titan’s unique Direct-Coupled© circuit. Nova is a full system solution incorporating twelve independent power cleaning networks.
AVAILABLE OUTLETS
FEATURES
適用於所有音響或 AV 系統
Suitable for all audio or AV systems
RFI（射頻干擾）降低 80dB
RFI reduction 80dB
12 組優化電源處理插座能有效消除共模和差模電源雜訊
12 optimised power cleaning circuits remove Common and Differential Mode mains noise
8 組獨立插座供應訊源設備
8 independent outlets for source components
4 組獨立高電流插座，可供應功率擴大機、主動式超低音、主動式喇叭等
4 independent high current outlets for power amps, subwoofers, active speakers etc..
重新平衡正弦波來消除直流
DC cancellation through sine wave rebalance
216,000A 瞬時保護
216’000A instantaneous protection
全星型接地網絡
Fully star-earthed network
熱模連續鑄造法的單晶鍍銀銅導線，並帶有 FEP （氟乙烯丙烯）絕緣
Solid core Ohno Continuous Cast copper silver-plated internal wiring with FEP virtual air dielectric
附贈 IsoTek EVO3 PREMIER 電源線（1.5m）
Supplied with IsoTek’s award winning EVO3 PREMIER POWER CABLE
提供英國（UK）、歐盟（EU）、美國（US）、澳大利亞（AU）、中國（CH）等規格
UK, EU, US, AU & CH outlets available
設 計
EVO3 Nova 是一款配備四組高電流插座的十二迴全系統主電源處理，插座搭載 IsoTek 獨有的直接耦合（Direct-Coupled©）技術，能持續提供 3,680W 的功率，非常適合功率擴大機、主動式超低音、主動式喇叭等。此電路能夠在保持瞬態和動態表現的同時，提供最優化的高電流低阻抗過濾效果。
EVO3 Nova 為寬 445mm、深 370mm、高 185mm 尺寸規格的革新系統，不僅在功能上超越了 Aquarius 和 Sigmas 型號，更是音質提升的重大進步。具備六組獨立的插座，各自擁有專屬的電源淨化網絡，相當於集合了六組電源淨化網絡於一身。此系統不僅大幅減少差模與共模訊噪，每一輸出插座的多重淨化階段也極大的減少了互相干擾，這與市面常見的將插座串聯的電源處理器設計大相逕庭，該方式容易使音響設備產生的差模噪訊在插座間互相傳遞，從而影響音質。其精密的電路架構設計，Nova 的性能在電源處理領域中表現卓越，傲視同儕。
EVO3 Nova 配備了四組高電流低阻抗的輸出插座，每組插座的額定電流為 16A，可提供在 230V 時 3,680W 或 115V 時 1,840W 的功率輸出。這些插座專用於功率擴大機、重低音喇叭、主動式音響，並使用了 Titan 型號的 Direct-Coupled© 電路的輕量版本。其餘八組中電流插座的額定電流為 10A，專為訊源設備設計。搭載 IsoTek 獨有的 Adaptive Gating© 自動電源調控系統，能夠自動感測連接的負載，基於實際的功率抽取來提供最佳的電力透析效果，其電源淨化線路佈局比 Aquarius、Sigmas 型號更為精密高級。非常適合大型的音響系統或劇院系統安裝使用。
IsoTek 的 KERP©（Kirchhoff 等阻抗路徑）技術，確保所有插座獲得均勻一致的阻抗和功率輸出。內部配線採用最高標準，使用超純的 Ohno 單結晶連續鑄造銅芯，並在表面鍍上銀，使得電阻低、電流高。導體周圍有一層氟乙烯基丙烯（FEP）螺旋導管，再加上一層壓制的 FEP 絕緣保護導體，同時形成一個虛擬的空氣絕緣體（VDA）。這套結構確保了卓越性能，實現了極低阻抗和高性能的內部電力傳輸系統。此外，該系統還提供了高達 108z06,000A 的瞬時保護能力，透過 IsoTek 特有的序列化及可重複的保護系統，如盾牌般守衛您接連的貴重器材，確保其受到優質的安全防範。
EVO3 Nova 內建 Syncro 獨特的直流消除電子技術，重新平衡 0V 線上的電源正弦波，明顯降低或消除了變壓器的噪訊。這項精密設計的產品既可以獨立使用於單一音響設備，也可與 IsoTek 的電源淨化器結合使用，升級整個系統並在所有輸出插座中提供完全重新平衡的正弦波。在搭配 HI-FI 音響系統使用時，能帶來重大的音質提升。
EVO3 Nova 的設計質量卓越、功能實用，是整套音響系統電源升級的絕佳選擇。此設備有助於進一步提升音場、立體成像、低音清晰和控制力，營造一個更開闊和具有空間感的音場。此外，IsoTek 所獲獎項的 Premier 電源線也包含在內，共同為您的音響系統帶來全面性的音質提升。
IsoTek 的產品內部佈線與電源線產品相得益彰，這種設計思路著重於在整個傳輸線路中，無論是訊號傳輸線或是電源線，都保持設計與材質特性的一致性。這一經常被忽略的領域事實上是提升音響系統整體性能和聲音品質的關鍵環節。
DESIGN
EVO3 Nova is a twelve-way full system mains power cleaning solution comprising four high-current outlets, featuring IsoTek’s unique Direct-Coupled© technology, a system capable of delivering 3’680W of continuous power, ideal for power amplifiers, mono-block amplifiers, subwoofers, and active loudspeakers. This circuit provides optimal high-current low impedance filtering while fully maintaining transient and dynamic performance.
The EVO3 Nova is an innovative component with a power cleaning and distribution system measuring 445mm in width, 370mm deep and 185mm high. It is a significant step up from both the Aquarius and Sigmas models. Nova really is a full-scale power cleaning system incorporating twelve power cleaners in one box all output sockets are independent, each one with its own dedicated power cleaning network; these dramatically reduce both Differential Mode and Common Mode noise. Cross contamination of connected components is also kept to a minimum due to the multiple power cleaning stages for each output socket. Most power filters join output sockets together, running each in series. This is an error as Differential Mode Noise created by your connected electronics will cross contaminate from one output socket to the next. The electrical architecture and design of Nova is dramatically superior.
There are four high current low impedance outlets, rated at 16A, delivering 3’680W at 230V or 1’840W at 115V, these are suitable for power amplifiers, active loudspeakers or sub woofers and feature a light version of the Titan’s Direct-Coupled© circuit. The eight remaining medium current outputs rated at 10A are designed for source components. These feature IsoTek’s unique Adaptive Gating© technology that autosenses the connected load, thus giving the ideal optimal clean power based upon power draw. The power cleaning network is more sophisticated than that of Aquarius or Sigmas models. Nova is ideal for large scale audio or audio-visual installations.
KERP© (Kirchhoff’s Equal Resistance Path) ensures equal resistance and equal power delivery to all outlets. The internal wiring is of the highest standard; ultra-pure Ohno Continuous Cast copper solid core conductor strands with silver-plating offers low resistance and high amperage. A Fluorinated Ethylene Propylene (FEP) helix is wound around the conductor before an extruded FEP dielectric protects the conductor and creates a Virtual Dielectric of Air (VDA). This construction gives unrivalled performance and gives the ultimate low resistance, high performance internal power delivery system. Furthermore, 108,000A of instantaneous protection is provided, safeguarding valuable equipment via IsoTek’s unique sequential and repeatable protection system.
Also built into the Nova, is the Syncro unique DC-cancelling circuit that rebalances the mains sine wave on the zero volts line, to dramatically reduce/silence transformer hum; the circuit synchronizes the mains supply to provide a perfectly symmetrical sine wave, which also delivers significant sonic improvement when used with any hi-fi separates.
Nova is high quality design, highly functional and an excellent upgrade for a complete high-end audio or audio video system improving sound stage, three-dimensional imaging, bass articulation, control and a sense of extended frequency range and openness. IsoTek’s award winning Premier power cable is also included.
The internal wiring of IsoTek products synergizes with the range of IsoTek power cables. One critical but overlooked area is maintaining commonality of design and material properties though an audio wiring loom, be it signal carrying cables or your power cable network.
消除電源噪音 REMOVES MAINS NOISE
差模噪訊是用電源噪訊是由所有插電的電器裝置產生的。實際上，就是所有有電源的東西，例如您的微波爐、電視、電腦，以及您擁有的音響器材。
共模噪訊通常被稱為射頻干擾（RFI） – 這是我們周圍有但看不見的傳輸頻率。例如，行動電話、基地台、Wi-Fi 和藍牙系統等等無線頻率讓 “共模噪訊” 不斷增加，想像一下智能手機和平板電腦傳輸的數據量有多大；而廉價的電源線就像天線一樣，接收這些不需要的頻率。
Differential Mode mains noise is created by all electrical appliances – everything with a power supply, in fact. This includes your microwave oven, your television and your computer, as well as every hi-fi component you own.
Common Mode mains noise is often referred to as RFI – transmitted frequencies that surround us but we cannot see. For example, imagine how much data is transmitted by smartphones and tablets; cheap power cables act as aerials (antennas) for these unwanted frequencies.
正弦波校正 SINE WAVE CORRECTION
從高品質聲音的需求來看，電源需要兩個重要條件：1. 必須有穩定的 50 或 60Hz 正弦波，來源要是低阻抗的。2. 沒有無線射頻噪訊干擾。
低阻抗確保無論周圍區域使用多少電力，電壓都能維持相對穩定。然而，實際上我們可能會有約 5% 的電壓波動。主電力在 50 或 60Hz 時的極低阻抗（低於 1 歐姆）在接近無線電頻率（> 50 歐姆 > 100 千赫）時無法保持，反而充當天線，吸引無線射頻噪訊。
IsoTek 的電力淨化電路的設計目標是在保持安全性的同時，降低阻抗，並在音訊頻率範圍內進行有效校正。這不僅僅是基於良好的電力工程判斷，同時也符合電氣安全規範，經過獨立評估。
From a high quality audio point of view, mains electricity needs two factors; a nice 50 or 60Hz sine wave supplied from a very low impedance source, without radio frequency noise. The low impedance makes for a near constant voltage regardless of how much power is used in the surrounding area. In reality we can typically expect around 5% fluctuation. The very low impedance of the mains, which is way below 1 ohm at 50 or 60Hz is not maintained when approaching radio frequencies (> 50 ohms > 100 kHz) and acts as an aerial (antenna) inviting RF noise.
IsoTek’s power cleaning circuits are designed to reduce impedance whilst remaining safe as well as correcting well into the audio frequency bands. This is not only a judgment from sound electrical engineering, but it also follows the codes of electrical safety, which are independently assessed.
多重濾波系統 MULTIPLE FILTER SYSTEM
IsoTek 的許多產品不僅僅是單一的電源淨化系統，更是將多個電源淨化器巧妙結合在一個極簡設計的機箱中。其優勢在於每一台音響器材都擁有專用的淨電供應系統。
這種設計不僅將差模式噪聲降至最低，同時消除了插座與插座之間的電噪訊交叉污染的可能性。
與許多電源淨化系統不同，它們只是將標準濾波器設計置於一個機箱中，”將所有插座按照串聯方式連接。這樣的結構會導致連接的設備相互交叉污染”，使得產品失去了效能。
因此，IsoTek 的多重濾波系統確保每個音響器材都能獨享專屬的乾淨電源環境，徹底提升整體音響系統的性能。
Many IsoTek products are not just a single power cleaning system but are multiple power cleaners in one convenient chassis. The advantage being that each component in your audio system has own dedicated clean power delivery system. Furthermore, Differential Mode noise, created as electrical devices draw power, is kept to a minimum and the possibility of electrical noise cross contamination between outlet sockets is eliminated.
Many power cleaning systems simply place a standard filter design in a box with all outlet sockets joined together in series one after the other, thus connected equipment cross contaminates and the purpose of the product is lost.
獨立模組插座 INDEPENDENT SOCKETS
IsoTek 的產品採用完全獨立的插座，彼此之間沒有直接連接。這對於限制或消除差模式電噪訊的交叉污染是一個至關重要的點。
每個插座直接連接到電路板，並由 IsoTek 獨特的電源處技術提供服務。
IsoTek products feature outlet sockets that are totally independent from each other; no two outlet sockets being directly connected. This is a critical point for limiting or eliminating the cross contamination of Differential Mode mains noise.
Each socket connects directly back to the PCB and is serviced by IsoTek’s unique power cleaning technologies.
進階組件 HIGH GRADE COMPONENTS
IsoTek 每項產品用的都是頂級電子元件，許多都是特製的，並使用高品質金屬材料。品質的追求不僅止於零件，更延伸至印刷電路板（PCB），該設計能維持高電流輸出和超低電阻，使用的銅量高達一般標準的八倍，再加上純銀鍍層。
內部配線則選用高純度銅結合鍍銀工藝，絕緣材料是航太級的氟化乙烯丙烯（FEP）或 IsoTek 獨有的虛擬空氣 介電（VDA）技術，纏繞 FEP 管再加上 FEP 絕緣層，確保了卓越的傳輸表現，打造出低阻抗、高功率的內部供電系統。
Every IsoTek product uses the finest grade electrical components, many custom made, using the highest quality metals and materials which are specifically designed for purpose. Quality doesn’t stop at parts but also extends into the PCB designs, which maintain high levels of amperage and extraordinarily low levels of resistance, using up to eight times the general standard of copper prior to pure silver plating.
Internal wiring also uses high purity coppers combined with silver plating, with either Fluorinated Ethylene Propylene (FEP) dielectric or IsoTek’s Virtual Dielectric of Air (VDA), where a FEP tube is wound around the conductor before an extruded FEP dielectric protects this construction giving unrivalled performance and the ultimate low resistance, high performance internal power delivery system.
突波保護 SURGE PROTECTION
在電源供應系統中，電力突波或電湧對於任何電器都相當不利，尤其是高音質音響系統來說，影響更是明顯。當電源線上的電荷突然爆增時，就會發生電力突波，這會使得電位能量升高，並導致更多的電流流向牆上插座，進而損害您精密的音響系統。
IsoTek 的保護系統配置了一系列壓敏電阻（VDR）串聯防護技術，可提供多達超過 100,000A 的保護等級。根據電源突波或電湧的嚴重程度，快速且順序地介入而當情況需要時，保護電路設計得能立即大範圍反應。
保護電路有兩大主要功能：其一是保護自身，其二是隨著問題的加劇循序介入，對於極端情況則能做出快速反應同時也確保了濾波器的安全，而濾波器在首波保護中也扮演了輔助角色不同於其他保護裝置僅提供保護作用，這些設置還有助於音質提升。研究指出，這樣的問題不僅明顯而且發生頻繁，特別是在 1,000 至 6,000 伏的高壓範圍下更是一大挑戰。許多保護系統未能即時提供足夠的保護，且可能還會影響音質。
Power surges or spikes on the mains supply are generally very bad for any electrical device especially a high quality audio replay system. Power surges occur when there is a boost to the electrical charge at some point in the power lines. This causes an increase in the electrical potential energy, which can increase the current flowing to your wall outlet. This in turn can damage your sensitive audio system.
The IsoTek protection system uses an array of VDRs which offer a cascading level of protection, in some cases over 100,000A. These step in fast and sequentially dependent upon the severity of the encountered power surge or spike. The architecture of the protection circuit extends dramatically and almost instantly when required.
The protection circuit has two primary functions, one to preserve itself and the second to step in gradually as any problem increases, with the ability to act very fast should an extreme condition occur. The protection circuits also protect the filters and the filters assist the protection in the initial stage. Unlike many protection devices these assist sound quality as well as providing protection. Studies suggest this problem is not subtle and is frequent. The disturbing challenge is the 1,000 to 6,000V range. It is likely most protection systems do very little good and probably cause sound degradation.
自動電源調控系統 ADAPTIVE GATING
IsoTek 獨特的自動電源調控系統，就像一位智能的電源管家，它能根據連接的設備自動調整，確保提供最佳的電力透析效果，同時保持符合電流需求。
這套系統還能防止不同的噪訊相互影響，就像隔離了插座間的噪訊交叉污染，這樣使用時，每個設備都能使用到最乾淨的電源，且不會影響其他設備的表現。
IsoTek’s unique Adaptive Gating system determines the appropriate level of differential filtration for any connected load. The maximum level of overall power filtration is achieved whilst respecting current requirements.
This system also eliminates Differential Mode noise cross contamination between outlet sockets, as all connected devices will corrupt the supplied clean power upon consumption throwing back Differential Mode noise. It is vital that this noise isn’t allowed to affect another component’s performance.
克希何夫 等效電阻電路 K.E.R.P.
根據克希荷夫 的技術論文所示，電路定律是處理電路中電流和電位差（通常稱為電壓）的兩個相等性原則，特別適用於集總電路。這些法則於 1845 年由德國物理學家古斯塔夫·克希荷夫 （Gustav Robert Kirchhoff）首次描述，擴展了喬治·歐姆的研究，並先於詹姆斯·克拉克·馬克士韋的工作。被稱為克希荷夫電路定律（Kirchhoff Circuit Laws）簡稱為克希荷夫定律，它們在電氣工程中得到廣泛應用，形成了電力網路分析的基礎。
IsoTek 對電路的設計受到 克希荷夫的兩個電流定律的引導。簡單的比喻是，如同 自來水廠得到一公升水，希望能無損失的輸送出一公升的水！
換句話說，克希荷夫和高斯描述了透過城鎮的概念解決看似不可能的問題。如果交通在城鎮周圍的圓形軌道上流動，對城鎮沒有影響。然而，一旦交通進入城鎮，就會對城鎮產生影響，而進入的車輛最終都必須離開。城鎮的結構將對這種遷移產生正面或負面的影響。在電子學中，這也是一個重要的觀念，我們必須全面尊重 信號路徑，因為無論是否願意，最終一切都將以不同程度存在於 訊號 路徑中。
Technical papers state that Kirchhoff’s circuit laws are two equalities that deal with the current and potential difference (commonly known as voltage) in the lumped element model of electrical circuits. They were first described in 1845 by German physicist Gustav Kirchhoff. This generalized the work of Georg Ohm and preceded the work of James Clerk Maxwell. Widely used in electrical engineering, they are also called Kirchhoff’s rules or simply Kirchhoff’s laws. These laws can be applied in time and frequency domains and form the basis for network analysis.
The guiding principles for IsoTek circuits are driven by Kirchhoff’s two current laws, a simple analogy would be that for every litre of water placed into a water distribution system we would expect to get the same out.
To put it another way, Kirchhoff and Gauss described how seemingly impossible problems could be resolved by the concept of a town. If traffic flows on a circular orbital road around the town there is no effect on the town. However, if traffic enters the town, then there will be an effect on the town, and however many cars that enter eventually have to leave. The structure of that town will have either a positive or negative effect on that migration. In electronics this is also true. We must totally respect the signal path as, whether one wishes it or not, ultimately everything will be in the signal path to a greater or lesser degree.
OCC單結晶銅鍍銀 SOLID OCC COPPER AG
IsoTek 所有產品的內部電線都達到最高標準。使用超純的 Ohno 單結晶連續鑄造銅芯，並在表面鍍上銀，這讓電阻低、電流高。導體周圍有一層氟乙烯基丙烯（FEP）螺旋導管，再加上一層壓制的 FEP 絕緣，保護導體，同時形成一個虛擬的空氣絕緣體（VDA）。這套結構確保了卓越性能，實現了極低阻抗和高性能的內部電力傳輸系統。
IsoTek 的內部佈線與 IsoTek 電源線系列ㄧ起使用可確保持設計和材料特性的共通性。
As one would expect the internal wiring of any IsoTek product is of the highest standard, ultra pure Ohno Continuous Cast copper solid core conductor strands with silver-plating offers low resistance and high amperage. A Fluorinated Ethylene Propylene (FEP) helix is wound around the conductor before an extruded FEP dielectric protects the conductor and creates a Virtual Dielectric of Air (VDA). This construction gives unrivalled performance and gives the ultimate low resistance, high performance internal power delivery system.
IsoTek’s internal wiring synergizes with the range of IsoTek power cables. One critical but overlooked area is maintaining commonality of design and material properties though an audio wiring loom, be it signal carrying cables or your power cable network.
持續穩定輸出功率 CONTINUOUS ABSOLUTE POWER
IsoTek 致力於 提供充沛且穩定的電源供應，即在電力公司 法規允許的供應範圍內無限制的輸出電流。 IsoTek 設計的電源對於功率擴大機或高功率電子設備來說，能夠提供低阻抗和低直流電阻（DCR）的輸出，這樣可以避免電流受限並提升器材的動態表現。當電源 受到污染時 時，器材的動態範圍也會變差而且到電站之間 的迴路阻抗遠高於此。
從交流電源供應中獲得超過 100% 的輸出是不可能的。依交流電的基本原理是輸送電能而不是存儲能量，而且根據交流電運作原則，是不可能存儲能量。所以「電源儲備」在交流電路中本質上是不存在的，也不可能存在。
電源儲備所需的電壓會隨著歐姆定律增加，並不是說電壓不下降就是電能儲備。交流電（AC）波形在 50Hz 時，每 10 毫秒就在最大值和最小值之間變動，20 毫秒完成一整個週期。因此，實際上交流電（AC）波形的平均值為零。只有轉化為功率波時，由於負數平方變正的原則，而成為正值。以波形來看就像一個膨脹的正弦波，此時 45 度的值為 0.5，而不是三角形函數表中的 0.7071。如果只談電壓波，它長期來看是沒有值的，也就是零！所以談到能量儲存，實際上儲存的能量是零。
直流電阻（DCR）會電壓下降。換句話說，需要開發一個不限制發電站電力儲備的系統，這意味著電路需要在高感抗的同時，並具有極低的阻抗。如果方式正確並保持平衡，那麼在 50/60 Hz 時感抗幾乎為零，直流電阻（DCR）也非常接近零。因此，理想的過濾電路必須保持直流 0Ω 阻抗（或非常接近），並對高於 50/60 Hz 的噪訊具有相當的的交流阻抗。這正是選對材料規格最重要的地方。即便有時
候可能需要用到一些極其特殊的材料，但在重要的關鍵部分，是非常適合使用的。值得註意的是，IsoTek 的濾波設計可以在 50/60 Hz 保持極低的阻抗，但在該頻率上卻有極高的噪訊消除能力。
大多數交流電路不僅僅含有電阻元件，還會表現出電阻結合電容或電感的特性。在理想狀況下，電路中唯一允許存在的阻礙應當是電阻，且電阻值要極低，這就帶來了一個難題，是否追求高的暫態功率，還是要強大的淨化濾波能力來消除雜訊。驚人的是，確實可以兩者兼顧，但要實現這一目標，就得依靠那些極高品質、專為此特定目標設計和結構完全正確的元件，這些高度複雜並專業的元件，僅在特殊領域中才能找到，而 IsoTek 的優勢在於其有能力設計出這些獨特的電子元件。
IsoTek delivers absolute power, unrestricted current delivery within what the power company can supply, and regulations allow. Generally, for power amplifiers or high wattage electronics IsoTek provides output which offers extremely low impedance and low DCR, this completely eliminates (within the concepts of power filtering) any possibility of current restriction and enhances dynamic range, the impedance of the chain back to the power station being far larger. When power is contaminated, dynamic range is reduced.
It is impossible to get more than 100% out of the mains supply. The very principle of AC power is that it doesn’t store energy in the transmission system. It is therefore impossible to store energy in an AC system by the very principles by which it works. There can be no so-called power reserve, thus a power reserve within an AC circuit in the truest sense of the word does not and cannot exist.
Power reserve would require the voltage to increase as ohms law insists it must, saying a circuit doesn’t sag isn’t a reserve of power. The AC waveform goes between maximum and minimum points at 50 Hz in 10 mS, it then swings to the maximum negative value. At 20 mS a full cycle is achieved. Therefore, in fact the average values of an AC waveform is zero. Only as a power wave can it be positive, this is due to the law of squared negatives. It looks like a ballooned sine wave where the value of 45 degrees is 0.5 not 0.7071 from a trigonometric table. Were this only a voltage wave it would have a long-term value of zero! As far as energy storage is concerned zero is the value of stored energy.
Direct Current resistance (DCR) will cause sag. To put it in other words, a system has to be developed which does not limit the power reserve of the power station, meaning a circuit needs to have extremely low resistance whilst maintaining sufficiently high inductance. When done correctly and in perfect balance the inductance is virtually zero at 50/60 Hz and the Direct Current resistance (DCR) is also very close to zero. Therefore, an ideal filter circuit must maintain zero Ohms resistance DC (or very close) and considerable AC resistance to noise above 50/60 Hz. Despite statements to the contrary, this is precisely where correctly specified materials matter most. Whilst some might consider these ‘exotic’ they represent a critical and important part of the function and appropriate to use. Remarkably IsoTek filter designs can maintain very low resistance at 50/60Hz but have very high amounts of noise cancellation above that frequency.
Most AC circuits are reactive – produce a reaction either from the power drawn or the circuit itself, put simply they are not pure resistors and behave like a capacitance and resistance or an inductance and resistance. In an ideal world the only allowable impediment is resistance and ideally this needs to be extremely low. A dilemma, do you want high transient power, or do you want heavy filtration – amazingly you can have both, but one must have components of the very highest quality, which are designed specifically for purpose with totally correct architecture. This is extremely complex and has resulted in the design of specialist parts; these do not exist outside the world of specialist power engineering and are unique to IsoTek designs.
3年保固 THREE YEAR WARRANTY
IsoTek 始終堅持以最高標準的客戶服務。為體現我們對產品品質與客戶滿意度的持續承諾，將提供將標準 2 年的產品保固期免費延長至 3 年的機會。
您請簡單地進行產品註冊，您就可以安心享有此項增值服務。IsoTek 尊重並保護您的個人隱私，絕不會未經您許可而與第三方分享您的個人資料。
As part of our on-going commitment to the highest standards of customer service, IsoTek offers you the opportunity to extend the standard 2 years product warranty to 3 years, free of charge.
Simply REGISTER YOUR PURCHASE with IsoTek. We do not share your personal details with any third parties without your permission. To read our Privacy Policy please CLICK HERE.
SPECIFICATIONS
插座數量：12
NUMBER OF OUTLETS：12
插座輸出規格：英國（UK）、歐盟（EU）、美國（US）、澳大利亞（AU）、中國（CH）
TYPE OF OUTLETS：UK, EU, US, AU & CH
螢幕顯示資訊：Voltage / THD / off
DISPLAY：Voltage / THD / off
中電流 115V：x8 (10A 1’150W total)
MEDIUM CURRENT – 115V：x8 (10A 1’150W total)
高電流 230V：x4 (16A 3’680W total)
HIGH CURRENT – 230V：x4 (16A 3’680W total)
高電流 115V：x4 (16A 1’840W total)
HIGH CURRENT – 115V：x4 (16A 1’840W total)
電源輸入：16A IEC C20
MAINS INLET：16A IEC C20
輸出電壓：100-240V / 50-60Hz
MAINS VOLTAGE：100-240V / 50-60Hz
中電流 230V：x8 (10A 2’300W total)
MEDIUM CURRENT – 230V：x8 (10A 2’300W total)
突波保護：108’000A
SURGE PROTECTION：108’000A
尺寸（寬 x 高 x 深）：445 x 185 x 370mm
DIMENSIONS (W X H X D)：445 x 185 x 370mm
重量：15Kg
WEIGHT：15Kg
DOWNLOADS
CONNECTION DIAGRAM
PRESS RELEASES
價格 PRICE 2024
£7,995.00（當地售價）
